Page 4 of 4

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 12:19 pm
by karatestu
Dr Bunsen Honeydew wrote: Thu Jan 11, 2018 11:58 am Just pull harder it is a compression fit, it comes off.
Cheers Doc. Going to find the crowbar now :grin:

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 12:22 pm
by Dr Bunsen Honeydew
Just a sharp tug will do it.

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 12:28 pm
by SteveTheShadow
If it proves stubborn, jack up the platter against the top plate with a couple of wood wedges, then give the spindle a sharp tap with a hammer. That will shock the taper free. Works every time, just don't follow through with the hammer.

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 12:58 pm
by karatestu
Sharp tug applied :hand: and platter is off. :dance:

Thanks all. :clap: It is nice that the platter mat still has the little chrome ring near the spindle. Seen a lot of pics with it missing.

Time to start my own thread I think although progress will be slow. :epopc:

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 1:20 pm
by Dr Bunsen Honeydew
Don't forget the speaker project updates and the amp fiddling. You really should finish one first, where are the BBCubes up to now.

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 1:34 pm
by Alfi
Apologies, I'm late to removing platter..

Glad you got it off with a sharp tug Stu.

I put index finger in each hole in the platter and apply thumbs to spindle, pull with fingers and press with thumbs - platter comes of the taper easily, no need for wedges.

Alfi.

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 2:28 pm
by karatestu
Dr Bunsen Honeydew wrote: Thu Jan 11, 2018 1:20 pm Don't forget the speaker project updates and the amp fiddling. You really should finish one first, where are the BBCubes up to now.
Speakers haven't really moved on recently. Been too busy listening to the new LS6 I put in. Marvellous, I have never been so happy with the music. I will be doing more on them, I promise.

Too many things on the go, I know, I know :roll: I have lots to do with CDP and amps as well. I often find that one experiment (and the results) has a knock on effect with everything else so I go off on a tangent and play with something else for a while . It's like a merry go round and a bit exhausting at times but it's the way I work .

Head is full of stuff.

Re: Pioneer PL-71 Refurbishment

Posted: Thu Jan 11, 2018 2:32 pm
by karatestu
Alfi wrote: Thu Jan 11, 2018 1:34 pm Apologies, I'm late to removing platter..

Glad you got it off with a sharp tug Stu.

I put index finger in each hole in the platter and apply thumbs to spindle, pull with fingers and press with thumbs - platter comes of the taper easily, no need for wedges.

Alfi.
Cheers Alfi,

Your way sounds good as it won't shock anything. Had images of platter coming off at 100mph and smashing dust cover but it didn't take too much of a tug in the end :grin:

I will have two cartridges available to use. Lyra Argo (take it off my Aro) and the Asaka that comes with the PT1. Choices, choices.....

Stu

Re: Pioneer PL-71 Refurbishment

Posted: Fri Jan 12, 2018 1:08 am
by Dr Bunsen Honeydew
"Speakers haven't really moved on recently. Been too busy listening to the new LS6 I put in. Marvellous, I have never been so happy with the music."

Then you need to borrow the TSCS :twisted:

I will get him to sell his tractor before I am finished :lol: :lol: :lol: :twisted:


https://www.youtube.com/watch?v=QZY6jC5Dh6c

Re: Pioneer PL-71 Refurbishment

Posted: Fri Jan 12, 2018 9:07 am
by karatestu
I have that on vinyl and a Wurzels compilation CD. Gets played now again. How's about "Blackdird i'll 'ave 'ee" or "champion dung spreader" - classics :grin:

Yes Doc, you have hooked me big time. Will have to resist the urge to sell a kidney :guiness;