I have a tiny bit of sill to replace . It's what's left of the original sill where my heavy duty box section was joined. A small bit of 3mm steel will sort that out.
Starting to think about painting now
Stu
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
Re: Stu
Some repairs were required to a tiny section of the original sills where the front wings bolt on. Both front wings are off. Had to weld some new steel in . These bits didn't get replaced 9 years ago when the 3mm box section sills were put in because the front wings wouldn't have fit back on properly.
DIY FREE ZONE
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
Re: Stu
Got some proper primer on now rather than just the weld through stuff that went on first. Fuel tank is primed up and looks kinda sexy. Both sills are primed and all the new rear arches and bits of new floor.
Some bits had rust convertor applied three times . First coat left a few days and then removed. Same with second coat. Third was left on and then primed over the top. Degreasing and keying was all done to give the paint the best chance of adhering.
Some bits had rust convertor applied three times . First coat left a few days and then removed. Same with second coat. Third was left on and then primed over the top. Degreasing and keying was all done to give the paint the best chance of adhering.
DIY FREE ZONE
- slinger
- Posts: 9683
- Joined: Wed Aug 22, 2012 4:30 pm
- Location: The Garden of England
- Has thanked: 5392 times
- Been thanked: 3418 times
Re: Stu
It's definitely rockin' that orange, Stu.
Amps - NVA P50, AP30, A40, Stanislav Palo Tube Headphone Amp BB 85
Speakers - Monitor Audio Silver RX2
Cables - NVA LS1+LS3, SSC, Gotham S/PDIF, IBRA Optical
Digital - NAD C516BEE, SONY ST-SDB900 DAB TUNER, TEAC UD-H01 DAC
Analogue - Pro-Ject Debut Carbon Esprit SB, Graham Slee Gram Amp 2 Phono
Cans - Grado SR80, ATH-M50X
Speakers - Monitor Audio Silver RX2
Cables - NVA LS1+LS3, SSC, Gotham S/PDIF, IBRA Optical
Digital - NAD C516BEE, SONY ST-SDB900 DAB TUNER, TEAC UD-H01 DAC
Analogue - Pro-Ject Debut Carbon Esprit SB, Graham Slee Gram Amp 2 Phono
Cans - Grado SR80, ATH-M50X
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
Re: Stu
Unfortunately it's only primer so will be covered with top coat. As I don't want the hassle of changing details on the V5 or the potential insurance increase from declaring modifications then the majority of the vehicle will have to stay the original colour.
I am painting these new bits, the front & rear bumpers, plastic wheel arch extensions, sills and bottom of doors in Upol Raptor textured bed liner. It's matt black and tough as he'll- doesn't chip and scratch like most paints. It was designed initially for the load area of pick up trucks where things get thrown in and dragged out. There is quite a trend these days with people painting their whole vehicle with it. That is my intention (eventually), with the bottom being black and the top the original colour (raptor is tintable).
It's a bit of a marmite paint as some love it and others hate it. It's bumpy and not a shiny gloss. It is much more forgiving of preparation, slight imperfections get covered up and it is super tough. As this vehicle works for a living and goes off road most work days then it makes sense . Plus I've never been one for giving a shit what it looks like as long as it does its job and stands the test of time without costing me a fortune.
DIY FREE ZONE
- slinger
- Posts: 9683
- Joined: Wed Aug 22, 2012 4:30 pm
- Location: The Garden of England
- Has thanked: 5392 times
- Been thanked: 3418 times
Re: Stu
The old "functionality over form" argument. I can see that.
Amps - NVA P50, AP30, A40, Stanislav Palo Tube Headphone Amp BB 85
Speakers - Monitor Audio Silver RX2
Cables - NVA LS1+LS3, SSC, Gotham S/PDIF, IBRA Optical
Digital - NAD C516BEE, SONY ST-SDB900 DAB TUNER, TEAC UD-H01 DAC
Analogue - Pro-Ject Debut Carbon Esprit SB, Graham Slee Gram Amp 2 Phono
Cans - Grado SR80, ATH-M50X
Speakers - Monitor Audio Silver RX2
Cables - NVA LS1+LS3, SSC, Gotham S/PDIF, IBRA Optical
Digital - NAD C516BEE, SONY ST-SDB900 DAB TUNER, TEAC UD-H01 DAC
Analogue - Pro-Ject Debut Carbon Esprit SB, Graham Slee Gram Amp 2 Phono
Cans - Grado SR80, ATH-M50X
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
Re: Stu
Just when you thought it was safe to put the welder away . Front bolt on wings and front bumper.
Bumper has two bolt on plastic corners. Daihatsu spot welded a steel bracket on each end of the metal bumper give support to the plastic corners. These are right in front of the front wheels and have no protection from splash. Both sides were rotten so cut out and repaired with 1.5mm steel and no silly brackets added back.
Bumper has two bolt on plastic corners. Daihatsu spot welded a steel bracket on each end of the metal bumper give support to the plastic corners. These are right in front of the front wheels and have no protection from splash. Both sides were rotten so cut out and repaired with 1.5mm steel and no silly brackets added back.
DIY FREE ZONE
- karatestu
- Posts: 6090
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1931 times
- Been thanked: 1621 times
Re: Stu
Front wheel arches are no way near as badly rusted as the back. Near side wing required on small repair. The off side was worse which is usually surprising as it is not in the puddles at the side of roads. In this case the rot is due to the collision which occurred in 2015. The wing was never repaired properly and the damage was actually behind the plastic arch extension. I left the mud flap off since 2015 as the wing was pushed forward a little which made the mud flap touch the tyre on certain locks of the front wheel.
A proper repair was overdue. It was rotten behind the plastic arch extension in one place just behind the front wheel. This was cut out and repaired with 1.5mm steel. Had to do it in several pieces as the contours were too complex. It's now all tacked together and ready for full welding. One piece needs trimming back - the irregular shaped one which creates the curve of the arch.
A proper repair was overdue. It was rotten behind the plastic arch extension in one place just behind the front wheel. This was cut out and repaired with 1.5mm steel. Had to do it in several pieces as the contours were too complex. It's now all tacked together and ready for full welding. One piece needs trimming back - the irregular shaped one which creates the curve of the arch.
DIY FREE ZONE