If it pleases YOU then that is all that matters. So, you have made them semi omni ? And what type of cap did you buy for the tweeter ? And have you had to put a padding resistor on the tweeter ?
Cheers
I used the cap from the tweeter crossover in the linns, no resistor- what’s its effect?
I read on the Richard Allan site that the tweeter is ‘full range’- don’t understand that really so just added the cap.
Analogue Source -
GL-59 modified.
ARB uni pivot alloy wand-AT-VM95SH- RigB 9
ARB uni pivot wooden wand-AT- Signet.
Quad 34 Pre amp with mm phono stage.
Ifi Zen Phono for mc
Akai 4000DS mk2 R2R Digital Sources- Argon Pi4 v2; IfI iUSB 3.0, Ifi Neo idsd Dac;
Fibre Ethernet connection.
Tidal / Radio Paradise Amplification Nva 300va mono blocks Speakers Lii Audio F-15 with Doc modded 12” in Open Baffle; Ls6
Weiduka AC8.8- for digital sources
Mini BMU for analog sources
Analogue Source -
GL-59 modified.
ARB uni pivot alloy wand-AT-VM95SH- RigB 9
ARB uni pivot wooden wand-AT- Signet.
Quad 34 Pre amp with mm phono stage.
Ifi Zen Phono for mc
Akai 4000DS mk2 R2R Digital Sources- Argon Pi4 v2; IfI iUSB 3.0, Ifi Neo idsd Dac;
Fibre Ethernet connection.
Tidal / Radio Paradise Amplification Nva 300va mono blocks Speakers Lii Audio F-15 with Doc modded 12” in Open Baffle; Ls6
Weiduka AC8.8- for digital sources
Mini BMU for analog sources
Analogue Source -
GL-59 modified.
ARB uni pivot alloy wand-AT-VM95SH- RigB 9
ARB uni pivot wooden wand-AT- Signet.
Quad 34 Pre amp with mm phono stage.
Ifi Zen Phono for mc
Akai 4000DS mk2 R2R Digital Sources- Argon Pi4 v2; IfI iUSB 3.0, Ifi Neo idsd Dac;
Fibre Ethernet connection.
Tidal / Radio Paradise Amplification Nva 300va mono blocks Speakers Lii Audio F-15 with Doc modded 12” in Open Baffle; Ls6
Weiduka AC8.8- for digital sources
Mini BMU for analog sources
Those cone tweeters look naff to people with no knowledge but they are surprisingly good, not as extended as a good modern dome tweeter but very sweet and musical.
When you say extended do you mean the frequency range or the ‘projection/dispersion ‘
Analogue Source -
GL-59 modified.
ARB uni pivot alloy wand-AT-VM95SH- RigB 9
ARB uni pivot wooden wand-AT- Signet.
Quad 34 Pre amp with mm phono stage.
Ifi Zen Phono for mc
Akai 4000DS mk2 R2R Digital Sources- Argon Pi4 v2; IfI iUSB 3.0, Ifi Neo idsd Dac;
Fibre Ethernet connection.
Tidal / Radio Paradise Amplification Nva 300va mono blocks Speakers Lii Audio F-15 with Doc modded 12” in Open Baffle; Ls6
Weiduka AC8.8- for digital sources
Mini BMU for analog sources
Hi again, I’m just about to install a set of doc modded 8” drivers, I would like some advice on the appropriate approach- I have been testing the wiring of each 8” plus a tweeter (cap only)- i can do it parallel at a total 8ohmn load max or in series at 16ohmn max, is there a preference you recommended using an A20,
I have a separate A20 directly feeding 10” Fane drivers rated at 16ohmn each so thought to match the diy cubes to these?
Cheers
Analogue Source -
GL-59 modified.
ARB uni pivot alloy wand-AT-VM95SH- RigB 9
ARB uni pivot wooden wand-AT- Signet.
Quad 34 Pre amp with mm phono stage.
Ifi Zen Phono for mc
Akai 4000DS mk2 R2R Digital Sources- Argon Pi4 v2; IfI iUSB 3.0, Ifi Neo idsd Dac;
Fibre Ethernet connection.
Tidal / Radio Paradise Amplification Nva 300va mono blocks Speakers Lii Audio F-15 with Doc modded 12” in Open Baffle; Ls6
Weiduka AC8.8- for digital sources
Mini BMU for analog sources
Bedroom Rig
PiCorePlayer Squeezebox clone, Allo Boss Dac, NVA AP10H with Stepped Attenuator upgrade and external PSU, Audioquest Nightowl Cans, NVA mini BMU